YoByTech Automation
AUTONOMOUS SMART ENERGY & GRID INTELLIGENCE

From Energy Source to Smart City Distribution.

YoByTech's Smart Energy & LPU Grid Platform automates how electricity is generated, stepped down at 33KV/11KV substations, dynamically routed to zones where maximum energy is required, conserved where not required, and protected by <1.2-second self-healing fault recovery from a single Central Command Control Center.

Smart Load Allocation

Routes maximum power to Hospitals, Factories & Peak Zones while auto-dimming idle streetlights & empty buildings.

Instant Fault & Disaster Recovery

Pinpoints cable/transformer faults within meters and reroutes power via Ring Main Units in <1.2 seconds.

Smart Energy 33KV/11KV Substation and Renewable Grid Control
LIVE • 33KV/11KV SUBSTATION & SOLAR GRID
City Grid Uptime & Self-HealingAutomated Load Balancing & Fault Isolation
99.9%
Interactive Smart Grid Control Simulation

Simulate City Power Flow, Load Priority & Quick Fault Healing

Interact with the 4 grid controls below to switch generation sources, open/close substation breakers, shift load priority, or trigger an 11KV electrical fault.

01 • ENERGY SOURCESOLAR + BESS ON

Solar & Battery Grid Boost

Injecting +140 MW clean solar & battery power into city grid.

02 • 33/11KV SUBSTATIONBREAKER CLOSED

Substation Main VCB Breaker

Breaker closed. Power flowing from 33KV substation to city.

03 • LOAD ALLOCATIONMAX PRIORITY

Where Max vs. Less Needed

Routing 310 MW max power to Hospitals, Plants & Peak Hubs.

04 • FAULT & RECOVERYGRID HEALTHY

11KV Feeder Fault Simulator

All 11KV ring feeders operating normally.

LIVE CITY POWER GRID TELEMETRY BUS

✅ Grid Balanced: Generating 480 MW • Priority Zones Receiving 310 MW • Saving 52 MW in Idle Zones

1. SOURCES

Thermal + Solar + BESS

480 MW Output

132KV / 33KV LIVEVCB Breaker
2. SUBSTATION

33/11KV & RMU LPU

58°C • PF 0.99

DIRECT FEEDER11KV Self-Healing Ring
3. MAX NEED ZONES

Hospitals & Plants

310 MW • 100% Priority

ECO-THROTTLEDSaving 52 MW
4. LOW NEED ZONES

Idle Streets & Offices

Auto-Regulated

City-Wide Intelligent Load Allocation

Where Max Energy is Required vs. Where Not Required

Smart Energy continuously analyzes real-time ward and feeder demand—directing maximum megawatts to critical zones while eliminating waste in low-demand zones.

HIGH-PRIORITY & PEAK DEMAND ZONES

Where Maximum Energy is Required

100% Guaranteed

1. Hospitals, ICUs & Emergency Life-Safety

Tier-1 Lifeline Priority

Requires uninterrupted 24/7 power with zero voltage sag. Protected by dual-ring 11KV feeders plus automatic solar/battery islanding.

2. Industrial Plants & Manufacturing Corridors

Heavy Shift Load

Requires heavy 3-phase megawatt loads during production shifts. LPU capacitor banks maintain 0.99 Power Factor to prevent voltage drops.

3. Municipal Water Treatment & ESR Pumping

Critical Utility Load

High-thrust river intake and WTP pumps require coordinated bulk power during reservoir filling windows.

4. Evening Residential & Commercial Peaks (6–11 PM)

Peak-Shaving Active

When AC and EV charging loads surge simultaneously, Smart Energy injects stored BESS battery power to prevent transformer overload.

IDLE & OFF-PEAK CONSERVATION ZONES

Where Max Energy is Not Required

25–35% Saved

1. Daytime & Late-Night Smart Streetlights

45% Streetlight Saving

Streetlights automatically switch OFF at sunrise via lux sensors and dim by 40–50% between 1 AM and 5 AM when traffic is zero.

2. Empty Commercial & Govt. Offices After 7 PM

Auto Off-Hours Cut

Smart building LPUs automatically shut down idle HVAC chillers, corridors, and non-essential lighting loads after working hours.

3. Under-Loaded Parallel Substation Transformers

Zero Iron-Loss Waste

During low-demand night hours, LPU switchgear automatically puts redundant parallel transformers into standby to eliminate no-load core losses.

4. Non-Urgent Bulk Pumping During Peak Tariff

Load Shifting AI

Defers non-urgent municipal pumping and EV fleet charging away from expensive 6 PM–10 PM peak grid stress hours to solar midday.

Fault Pinpointing, Quick Resolution & Disaster Continuity

Where Electrical Problems Happen & Our Quick Solutions

How Smart Energy detects exact fault locations in milliseconds, heals the grid automatically, and manages natural disasters.

PROBLEM 01 • UNDERGROUND / OVERHEAD CABLE FAULT< 1.2 Sec Auto-Heal

11KV Feeder Short-Circuit or Line Break

Where & How Problem is Pinpointed:

Detected instantaneously between two Ring Main Unit (RMU) nodes using Fault Passage Indicators (FPI) with ±5m GPS accuracy.

Quick Automated Solution & Recovery:

LPU automatically opens the two isolating RMU breakers around the damaged cable segment and closes the alternate ring tie-breaker in <1.2 seconds—restoring power to the rest of the ward immediately while dispatching the nearest line-repair van.

PROBLEM 02 • SUBSTATION TRANSFORMER OVERHEATINGZero Transformer Burnout

Transformer Bushing Hotspot or Oil Fault

Where & How Problem is Pinpointed:

Spotted on 33KV/11KV power transformers via 24/7 radiometric thermal imaging cameras and winding/oil temperature LPUs.

Quick Automated Solution & Recovery:

Before winding insulation fails or catches fire, the Substation LPU triggers Stage-2 cooling banks, sheds non-essential load, or seamlessly transfers the feeder load to the N+1 standby transformer.

PROBLEM 03 • VOLTAGE SAG, SURGE & PHASE IMBALANCE±1% Voltage Stability

Tail-End Low Voltage & Phase Overloading

Where & How Problem is Pinpointed:

Identified at neighborhood Distribution Transformers (DTs) when one phase draws excessive current during peak evening AC hours.

Quick Automated Solution & Recovery:

Automated On-Load Tap Changers (OLTC) and thyristor-switched capacitor banks step up voltage and inject reactive power within cycles, protecting household and industrial equipment.

PROBLEM 04 • CYCLONE, FLOOD OR MAIN GRID BLACKOUT100% Lifeline Continuity

Natural Disaster & Regional Grid Collapse

Where & How Problem is Pinpointed:

City-wide emergency triggered by cyclone wind speeds, substation waterlogging sensors, or state-grid transmission failure.

Quick Automated Solution & Recovery:

Executes Autonomous Microgrid Islanding: immediately switches Hospitals, Water Treatment Plants, and the Command Center onto dedicated Solar + BESS Battery + DG microgrids while safely tripping flooded street feeders to prevent electrocution.

Visual Architecture Infographics & Field Hardware

Source-to-Distribution Blueprint & Substation LPU Devices

High-resolution engineering infographics illustrating generation to city distribution, load heatmaps, and substation LPU hardware.

INFOGRAPHIC 01 • SOURCE TO DISTRIBUTION
Energy Source to Smart City Distribution 3D Infographic
END-TO-END POWER FLOW

Generation → 33/11KV Substation → City Grid

Shows how power from Solar Parks, Wind Turbines, Thermal Plants, and Battery Storage flows through automated 132KV/33KV/11KV substations to hospitals, industries, and smart homes.

INFOGRAPHIC 02 • LOAD HEATMAP & FAULT AI
City Energy Load Heatmap and Self-Healing Fault Isolation Infographic
SMART LOAD & SELF-HEALING

Max Demand Heatmap & <1.2s Fault Isolation

Visualizes city high-demand priority zones versus eco-dimmed zones on the left, and automatic Ring Main Unit (RMU) cable fault pinpointing and rerouting on the right.

HARDWARE 03 • SUBSTATION LPU & EDGE DEVICES
Smart Energy LPU Edge Gateway, Thermal Sensor, and RMU Actuator Devices
IP67 SUBSTATION HARDWARE

Substation LPU, Thermal Camera & RMU Actuators

Showcases YoByTech's DIN-rail Energy LPU (Local Processing Unit), 33KV/11KV radiometric thermal imaging sensor, motorized RMU breaker actuator, and 3-phase harmonic analyzer.

8-Stage Source-to-Distribution Architecture

Full Details: From Energy Source to City Distribution

Click any of the 8 stages below to inspect its live sensors, LPU decision intelligence, problem solved, and quick automated solution.

STAGE 01 • GENERATION & CLEAN ENERGY MIX

Multi-Source Power Generation (Thermal, Solar, Wind & Battery)

City Generation Mix480 MW Active
42% Clean Energy
01 • LIVE SENSOR INPUTS

What LPU Sensors Measure

  • Solar String Inverter & Weather Irradiance Sensors
  • Thermal / Hydro Turbine Megawatt Output Meters
  • Battery Energy Storage System (BESS) State-of-Charge LPU
02 • SMART ENERGY AI BRAIN

How Smart Energy Decides

Smart Energy forecasts city-wide hourly megawatt demand and prioritizes clean solar/wind generation first, storing excess daytime green energy in utility battery banks.

03 • AUTOMATED LPU ACTION

What Happens Automatically

Generation LPU synchronizes inverter frequency, dispatches stored battery power during evening peaks, and balances base-load thermal power.

Electrical Problem Prevented

Prevents renewable energy curtailment and sudden frequency drops when cloud cover reduces solar output.

Quick Automated Solution

Instant sub-second BESS battery injection stabilizes grid frequency at 50.0 Hz automatically.

CITY NERVE CENTER & DISASTER MANAGEMENT

Central Command Control Center

Smart Energy Central Command Control Center and Disaster Management
CITY POWER GRID: ALL 33/11KV SUBSTATIONS NOMINAL480 MW Active • 0 Unresolved Feeder Faults • PF 0.99
99.9% Uptime

360° City Energy Command Wall (ICCC)

Controls and monitors every generation source, 33KV/11KV substation, RMU breaker, neighborhood transformer, and smart streetlight from one central room.

Live Load Dispatch (Where Needed vs. Not Needed)

Operators and AI algorithms view live ward-level load heatmaps—boosting power to high-demand hospital/industrial zones and trimming waste in idle sectors.

Automated Fault Pinpointing & <1.2s Self-Healing

Pinpoints cable faults and transformer trips on the GIS wall within meters, automatically actuating Ring Main Units to restore power before consumers notice.

Cyclone & Grid Disaster Islanding Protocol

If the regional transmission grid collapses or floods hit, Central Command automatically islands critical city lifelines onto local Solar + Battery + DG backup.